1.規格型號和安規認證
MODEL NUMBER AND SAFETY CERTIFICATION
品名規格：系列號+額定電流+額定電壓+認證符號
Model Number: Part Number+Rated Current+Rated Voltage+Approvals.
例子[example]:
5CTU， 1A， 125V/250V
1)系列號 Part Number
2)額定電流 Rated Current
3)額定電壓 Rated Voltage
1-2 額定電流和額定電壓
Rated Current And Voltage
額定電流：32mA~20A
Rated Current: 32mA~20A
額定電壓：125V/250V AC
Rated Voltage:125V/250V AC
1-3 標示 Marking
保險絲上需有下列標示 The fuse shall have the following marking:
規格：特性符號+額定電流+額定電壓 Specification:Characteristic Symbol+Rated Voltage
63mA~800mA : _mA125V250V 1A~20A: _A125V250V
Trade mark:The Manufacture’s Logo+Part Number+Approvals
63mA~20A:
注意：對標示字樣大小沒有規定
Note:Size of the markings have not be specified.
2.適用範圍 SCOPE
適用於一般電子設備。Used in electronic equipment.
3.工程圖和結構 OUTLINE DRAWING AND STRUCTURE
3-1 工程圖（單位：mm）Outline Drawing and Dimensions(Unit:mm)
3-2 結構 Structure
|
編號No.
|
元件Component
|
材質Material
|
數量Quantity
|
|
1
|
熔絲 Wire
|
合金 Alloy
|
1
|
|
2
|
銅帽 Cap
|
黃銅鍍鎳 Brass with mickel plated
|
2
|
|
3
|
本體 Body
|
陶瓷管 Ceramic Tube
|
1
|
|
4
|
引線 Lead
|
鍍錫銅線 Tinned Copper wire
|
2
|
|
5
|
砂 Sand
|
石英砂 Quartz sand
|
1
|
4.外觀及形狀
4.APPEARANCES AND CONFIGURATION
4-1 外觀：不應有破碎、明顯的汙斑
4-1 Appearances:There shall no fragmentation and of remarkable blotch.
4-2 形狀：帶腳的保險絲
4-2 Configuration:Axial Leaded Fuse.
5.物理特性
5.PHYSICAL CHARACTERISTIC
5-1 拉力測試
5-1 Tensile test
沿端子的軸向施加 10N 的拉力，持續 1 分鐘。
Keep pulling the cap of the fuse with 10N at axial direction for 1 min.
6.電氣特性
ELECTRICAL CHARACTERISTICS
熔斷/電流特性：
Pre-Arcing Time/Current Characteristic
a、Breaking capacity（分断能力）(Time Lag and Fast Acting)
1500A/1000A 125V/250V AC
b、Electrical characteristics
美标（UL）
|
RATED CURRENT
|
1IN
|
1.35IN
|
2IN
|
|
32mA-20A
|
Min.
|
Min.
|
Max.
|
Min.
|
Max.
|
|
4H
|
15S
|
1H
|
0.5S
|
5S
|
c、Temperature character
当100%的电流下温度上升不超过75℃
When 100% of rating the temperature rise doesn’t exceed 75℃.
d、Code&Approvals:
Temperature Rerating Curve
Average Time Current Curves
7.環境特性
7.ENVIRONMENTAL SPECIFICATION
7-1 操作溫度範圍：-5℃~60℃
7-1 Operating Temperature: -5℃~60℃
7-2 保存條件
7-2 Storage Conditions
溫度：+10℃~60℃
Temperature: +10℃~60℃
在相對濕度≤75%下平均可存放 3 年
在非露天下，相對濕度為 95%下最多可存放 30 天。
On average, It can be stored below the relative humidity or 75% for 3 years.
Without dew, It can be kept under humidity of 95% for 30 days.
8.焊接條件
8.SOLDERING PAAMETERS
8-1 波峰焊
8-1 Wave Solder
焊接溫度：260±5℃
Soldering Temperature:260±5℃
焊接時間：4 Sec. Max.
Soldering Time:4 Sec.Max.
8-2 手工焊錫
8-2 Manual Solder
焊接溫度：350±5℃
Soldering Temperature: 350±5℃
焊接時間：3 Sec. Max.
Soldering Time: 3 Sec. Max.
9.其他使用注意事項
9.OTHER NOTICE IN USING
如果需在保險絲上加熱縮套管，烘烤溫度與時間需參照以下規定
If heat shrink tubing was needed,the roast temperature and time should be refer to the following.
設定烘烤溫度：不大於 150℃ 烘烤時間：50s Max.
The temperature should be sel under 150℃,roast time:50s Max.
广告
