G-Switch 东莞品赞电子科技有限公司www.dg-
|
SPECIFICATION
規格書
|
Designation 品名:
|
Φ3.5 PHONE JACK
|
Model No. 型 號:
|
PJ-0287D00
|
1. Rating額定值:
|
DC 30V 0.5A
|
2. Operation temperature range 使用溫度範圍:
|
-20℃~+70℃
|
3. Preservative temperature range 保存溫度範圍:
|
|
4. Construction dimension
結構尺寸:
|
Apply to the appended drawing:
符合附加圖紙
|
Item 项目
|
Test condition 測試條件
|
Specification規格
|
5. Electrical characteristics電氣性能
|
5A
|
Contact Resistance
接觸阻抗
|
Being measured at 1KHz small current
contact esistance meter.
在1KHZ小電流下測量.
|
30mΩ max.
30毫歐以下.
|
5B
|
Insulation Resistance
絕緣阻抗
|
Measurements shall be made following
application of DC
250V potential across terminals and across
terminals and frame for 1 minute.
在端子之間和端子與殼之間加DC 250V條件下,
持續1分鐘測量.
|
100MΩ min.
100兆歐以上.
|
5C
|
Withstand Voltage
耐電壓
|
AC 500V (50Hz or 60Hz) shall be applied
across terminals and across terminals
and frame for one minute.
在端子之間和端子與殼之間加AC 500V
(50HZ或60HZ)條件下,持續1分鐘測量.
|
There shall be no breakdown.
無擊穿現象出現.
|
6. Mechanical characteristics 機械性能
|
6A
|
Insertion and
Extraction force
插拔力
|
Being measure at across spring piece
and across matching plug for ergometer.
用測力計在插頭與彈片之間進行測量.
|
Insertion and extraction force: 3~25N
插拔力: 3~25N
|
6B
|
Terminal Strength
端子強度
|
A static force of 5N being applied in
one direction on the tip of terminal
for 10sec.
将5N之靜負荷施加於端子頂部的一個
方向持續10秒。
|
(1). Contact resistance: 30mΩmax.
接觸阻抗:30毫歐以下.
(2). Insertion and withdraw force: 3~25N
插入力和拔出力:3~25N
(3). Electrical characteristics and
mechanical characteristics shall
be satisfied.
Without distinct damage.
机械,电气性能满足规定要求,无异常发生
|
7. Durability 耐久性
|
7A
|
Soldering test
可焊性試驗
|
The tip of the terminals shall be dipped
2mm in the solder bath at a temperature
of 240±5℃ for 3±0.5sec.
端子頂部被浸入焊錫池2mm深,溫度
240±5℃,時間3±0.5秒。
|
A new uniform coating of solder
shall cover a minimum of 95%
of the surface being immersed.
浸入的部分95%以上表面將被錫覆蓋.
|
7B
|
Resistance to
soldering heat
耐焊接熱
|
The jack shall be put into at the temperature
of 250±5℃ in 5±1sec(Automatic soldering)
or 380±5℃ in 3±1sec(Manual soldering)
after which measurement shall be made.
将产品端子浸入锡炉, 250±5℃,5±1秒
(自动焊);
380±5℃,3±1秒(手工焊)
|
(1). Contact resistance:30mΩmax.
接觸阻抗:30毫歐以下.
(2). Insertion and withdraw force: 3~25N
插入力和拔出力:3~25N
(3). Electrical characteristics and
mechanical characteristics shall
be satisfied.
Without distinct damage.
机械,电气性能满足规定要求,
无异常发生
|
Remark
備 註
|
G-Switch 东莞品赞电子科技有限公司 www.dg-
|